how to paint a plastic bathtub in a mobile home
However you dont want to prematurely apply the primer. Repeat this process until the entire interior is painted and then move on to the outside of the tub.
Do S And Don Ts For Painting A Plastic Tub In A Mobile Home Plastic Bathtub Bathtub Remodel Mobile Home
Let it dry for at least 24 hours.
. Apply at least two coats of paint to get more even and consistent coverage. First things first clean the walls. To be clear you want to use a bonding agent.
With the tub surround removed the lip of the tub will be exposed. Finish any cracks and chips with putty and sponge and apply a latex primer with the help of a roller. This will rough up the gloss so that paint easily adheres.
Keep the spray gun about 8 inches 20 cm away from the tub. Mobile home bathrooms with alcove bathtubs are a bit different from your standard site-built home alcove tubs. You have 2 options to combat the size difference if you want a standard bathtub.
It will also help your paint to adhere which is essential if you want your paint job to be as long-lasting as possible. Grab your angle brush and use the technique of cutting in edges to get complete coverage in the nooks and crannies. Alternatively use a nonabrasive tub and shower cleaner.
Step 1 Fill in cracks and crevices using a product recommended for your bathtub material. Cut through the threads and the rim of the fitting but not deep enough to go into the tub itself. Before you sand prime or paint you need to thoroughly clean the cabinets.
If the old tub surround is held in place with plastic rivets cut off the head with a knife or drill them out. Scrub the bathtub with Comet Cleaner and Scour Pads. Wait 24 hours then apply a second coat of enamel spray paint.
First the surface must be chemically cleaned to remove any soap scum mineral deposits or body oils. Finally remove the painters tape give your walls some time to dry and youre done. The standard tub in your mobile home is probably around 6 smaller both width and lengthwise.
Use Lime Cleaner to remove any lime or calcium buildup or stains. Complete 54 x 27 Bathtub With 1 Piece Surround. Let the taping compound fully dry.
Surface must be dry and warm. For mobile home bathtubs made from ABS plastic Plastimed appears to be the most recommended. Drill a 14 hole at both ends of the crack to help keep it from cracking any further.
As with any painting project the key to success is preparation. Clear the area around the tub of any debris such as hair soap residue and grime. Complete 54 x 27 Shower Pan With 3.
Use a high-quality enamel spray paint. Clean the cabinets first. Make a second cut about 12 inch away from the first cut.
Alongside your paint youll need a specific bonding agent to use as a primer. Buy a bathtub specifically made for mobile homes or buy builder-grade. Before you begin any bathtub refinishing job make sure the paint youve chosen specifically says its suitable for your bathtubs surface.
Next all cracks and chips are filled and sanded smooth. Finally grab a corner of the surround and carefully pull it off the wall. Immediately cover over the tape with another layer of joint compound applied with the 6-inch knife.
I wiped mine down with a solution of dish liquid and water just like dishwater then wiped them down again with clean water to make sure theyre all free of gook grime. Spray the tub surround with the cleaner. Combine 1 teaspoon of liquid dishwashing detergent with 1 quart of water in a spray bottle.
Knowing what your bathtub is made from is key to finding the right paint for the job. Do one pass with 400-grit paper and a second with the finer 600-grit. Next sand the entire bathtub using wetdry sandpaper.
Cover the wet compound with strips of joint tape and press it into place with a 4-inch drywall knife. Put on gloves and mix trisodium phosphate TSP and water according to the instructions on the box. 3 Piece Surround Currently Out Of Stock.
Dip a sponge in the solution wring it out and wipe down each cabinet. Be sure to follow all instructions given for mixing. Lightly sand the joint to smooth it down.
How to Prepare a Bathtub for Painting. This will help smooth out the surface of your plastic tub or shower and therefore allow your paint to go on more smoothly. Cover any cracks wider than 14 inch with a layer of fiberglass mesh that spans each side of the crack by at.
Then with a utility knife cut around the edge of the tub surround to loosen the caulk. Tape should extend a minimum. Pry out the cut segment with a flat screwdriver then use the screwdriver to pry up one of the edges of the drain fitting and unscrew it counterclockwise.
Once this is dry follow the instructions on the package proceed with the paint primer. Installation Instructions Prepare surface by removing all dirt grease tar oil etc. Apply this to your tubs surface using a roller for open surfaces and a paintbrush to cut in the hard to reach areas.
Painting yellow bathtubs in mobile homes arent too difficult. Use gentle strokes with the roller to avoid damaging the walls. I really like the new Dawn scent it.
The bathtub trim around that it should have been inside the drywall normally would put drywall over the top of that and then we can make it look real smooth. Allow the bathtub to dry then go over it entirely with 400 Grit Sandpaper. Work systematically by starting at a top interior corner and working your way across the length of the tub.
So all this would be textured and painted also means it has a hole this should have caught. Well put a PVC trim around that so it doesnt look so bad. Complete 54 x 27 Bathtub With 3 Piece Fiberglass Surround.
Remove all sanding dust from the bathtub with a damp cloth or a tack cloth. Be careful not to tear the vinyl coating on the panels as you sand. Then Miracle Methods proprietary bonding agent MM-4 is applied to ensure that the new finish adheres to the old surface.
Cut tape to cover crack. The best bathtub materials for painting are cast iron and acrylic though you can paint fiberglass bathtubs too. Coat the entire tub with long even motions.
